Showing results: 1831 - 1845 of 3397 items found.
-
34950A -
Keysight Technologies
The Keysight 34950A module for the 34980A Multifunction Switch/Measure Unit has 64 bi-directional lines configured as eight 8-bit channels. Each 8-bit channel has programmable polarity and thresholds up to 5V. The memory is useful for simulating and capturing digital patterns up to 10 MHz. It provides configurable handshaking protocols for a wide variety of applications.
-
B2987B -
Keysight Technologies
The B2987B Electrometer/High Resistance Meter is the world’s only graphical electrometer that allows you to confidently measure small currents with 0.01 fA (0.01 x 10-15 A) resolution and large resistances of up to 10 PΩ (10 x 1015 Ω). In addition, battery operation eliminates AC line noise from your critical measurements.
-
34450A -
Keysight Technologies
Turbo charge your production line with the Keysight 34450A 5.5-digit multimeter with OLED display. With its fast speed of up to 190 readings per second, you can increase your manufacturing throughput tremendously. Get highly accurate, repeatable, and trustworthy measurements with 0.015% DCV accuracy designed to meet general industrial and educational needs.
-
4U 84HP -
Kontron
As the established PICMG 2.0 CompactPCI has evolved, so has Hartmann Electronic’s product line. The 4U cPCI 9 slot solution is designed with quality and versatility in mind. This chassis comes complete with a 3U, 9 slot PCIe Gen3 backplane with single star topology, powered by two 300W cPCI Serial power supplies.
-
1506 IM -
Standard Electric Works Co., Ltd
● High quality Taut Band movement.● Battery operated.● Timer function for hands free use.● Battery indicator.● The tester measure with a frequency of 1kHz.● Measure speaker’s impedance.● Measure speaker lines (connected to load).● Help to calculate and check audio power systems.● Ideal for public address installation and maintenance.● Measure transformer impedances.
-
778673-01 -
NI
37-Pin Female D-SUB to 37-Pin Female Connector, Horizontal DIN-Rail Terminal Block - The CB-37FH is an unshielded terminal block that provides access to NI data acquisition devices with 37-pin female D-SUB connectors. The CB-37FH mounts in line with the DIN rail, and it features screw or spring terminals for connecting to 37 I/O signals, 12 to 30 AWG.
-
Suzhou 3ctest Electronic Co.,Ltd.
coupling/decoupling network is to test the capacity of high speed communication line for surge test. Data transmission rate is up to 1,000MBit/s. It is designed to meet the requirements of figure 14 in IEC/EN 61000-4-5: 2005. The material of decoupling device is high conductive magnetic material. Stable decoupling capacity and transmission rate, easy to use and compact size.
-
ELMA Electronic, Inc.
The Pioneer rack is the cornerstone of our broadcast cabinet line, offering flexibility, versatility and strength to meet the requirements of any broadcast application. Pioneer Seismic racks are offered in more than 25 different sizes, creating hundreds of configuration possibilities. A multitude of accessories are available, including shelving, cable management, cooling, power solutions and more.
-
Arcadia Test
At Arcadia Test, we understand that our Customers need Fixturing Solutions that rival todays technological advances. A fixture technology that met the requirements of the 1990’s, may not provide the necessary features required for todays complex test strategies. We developed our new line of Zion Wireless Test Fixtures with our Customers in mind.
-
AMC730 -
Vadatech Inc
The AMC730 is a a 10-Gigabit Ethernet (10GbE) AdvancedMCTM(AMC) module which includes an on-board line rate multi-core packet processor based on Cavium CN63XX CPU. VadaTech offers this product in a mid size (full size optional) form factor with the AMC.1, AMC.2 and AMC.4 specifications. The AMC730 is based around the Cavium OCTEON CN63xx processor which has been specifically designed to intelligently process Ethernet packets at line rate.The processor can be loaded via the PCIe/SRIO interface or via an optional flash memory. The number of processor cores, speed grade, and amount of DDR3 memory is customizable based on customer needs. The module has 2GB of HFA for pattern matching for deep packet inspection, etc. The SDK for the processor as well as additional software stacks are available from Cavium or third party.
-
OAKTON Instruments
This new addition to the Oakton EcoTestr product line features updates to make measuring water quality easier and faster. The display is larger with a better viewing angle, has indicators for battery life, readiness, and calibration, and shows both the parameter and temperature readings at the same time. To enhance field use, the cap was redesigned to be leakproof and can be attached to the top of the meter when not being used—no more lost caps! The cap features a fill line, so you know how much sample you need for an accurate reading when using the cap as a sample cup. It is also wider, providing a base to keep the meter upright for hands-free measurements. The keypad now has a fourth key to simplify menu navigation while keeping convenient one-touch calibration. The new housing is compatible with lanyards to prevent losing or dropping, but is still waterproof and floats just in case.
-
B-1007 -
ROSS ENGINEERING CORPORATION
Extra high voltage, low corona, grounding relays of the air insulated type. Peak test ratings up to 300kV and 100 amps continuous. Units can be operated either by solenoid, motor, or air cylinder, with spring or gravity return. All models have spherical contacts. When voltage transient limiting is required, some models have an adjustable sphere gap. Also available are units with built-in high voltage discharge resistors with energy dissipation capabilities from 50 to 10,000 ohms. Some units can be reduced in height if full line to ground voltage is connected to the top high voltage contact only and the other high voltage terminal is operating at, or near, ground potential. Line to ground voltage can also be increased by adding insulation between lower high voltage contact and ground. Normally mounted base down. Base up mounting if specified.
-
Columbia Research Laboratories
Columbia's SI-701 Series of Inclinometers are electronic tilt sensors based on Force Balance Accelerometer technology. They produce high level low impedance output proportional to the sine of the tilt angle. Model SI-701B is a low cost general purpose sensor that can be up-graded with the addition of the Columbia "HP" torquer system (SI-701BI) for greater accuracy and ruggedness. A bi-axial version of both units (SI-702B) is also available. The Model SI-701BI is designed with an output circuit made for 4-20mA data transmission systems for industrial applications. The model SI-701FND is a fluid dampened premium performance inclinometer designed to produce accurate tilt data in extreme shock and vibration environments. The latest addition in the line is Model SI-701WPBI, a waterproof (to 150 feet) inclinometer which operates from a +15 volt supply with 4-20mA output. A single power supply powers both the sensor and the 4-20mA line driver.
-
783486-01 -
NI
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
783485-01 -
NI
Kintex 7 160T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7821 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7821 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7821 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in-‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
